Four-Part Series: HP Latex Printer Accessories

Part Two – Using the Counterweights and Take-up Reel on Your HP Latex Printer

Printing panels for trade shows can keep a latex printer and a production manager busy, but there is one tip from HP Latex Specialist Timothy Mitchell that can help lighten the load a little: use the counterweights.

“There are a couple of key pieces to successfully panel printing with the 300 series latex printer,” Mitchell says of the counterweights. If you’ve never used them, they could still be on the dancer bar for the newer 300 series printers. For the older models (310, 330, 360), you may need to contact HP Support to order a set.

When panel printing, it is more efficient and accurate to reduce the tension on the media. The dancer bar adds tension and adjusting the counterweights on either end of the bar allows you to increase or decrease the tension, depending on the media thickness and material.

Another important tool to use properly is the take-up reel. Many people may not know that there is an option to wind the graphics inside or outside.

“If you go inside, there is a little less tension than if you go outside. I usually judge it by the media,” Mitchell says.

Much like adjusting the counterweights, winding media inside or outside depends on the media.

Watch the video above to see Mitchell discuss his tips and tricks for the counterweights and take-up reel. If you have an older 300 series printer, you can contact HP Latex Support.

If you have questions or are interested in learning more about printing with latex, contact a LexJet printer specialist at 800-453-9538 or visit LexJet.com.

Four-Part Series: HP Latex Printer Accessories

Part One – When to Use Platen Covers

If you’ve recently purchased an HP Latex Printer, there are some important tools you may not be using that can make printing a little easier: platen covers, counterweights, butterfly edge guards, and spindles.

In part one of our four-part series, we’ll discuss when to use platen covers.

Long, unattended runs on the latex printer is a great way for print service providers to complete large projects while staying on schedule with short runs or quick custom jobs. However, some PSPs experience issues when continuous runs are printed on fabric.

Because the media is porous and a heavier ink load is required (185-200% coverage), condensation can build up between the fabric and the platen and stain the image.

Timothy Mitchell, HP Latex Specialist, says that the platen covers, which are included with the Latex 365 or 500 series, are made specifically to reduce the condensation during these runs.

“These are there to prevent the accumulation of condensation and creating a discolored stain,” he says. “If I’m going to run an entire roll for a trade show, I will put these on because I am going to run continuously, and it will create a lot of moisture and the felt [on the platen cover] is necessary.”

Watch the video above to see Mitchell discuss the proper times and ways to use the platen covers. If you have an older 300 series printer, you can contact HP Latex Support.

If you have questions or are interested in learning more about printing with latex, contact a LexJet printer specialist at 800-453-9538 or visit LexJet.com.

Pro Advice: Keys for Trade Show Printing & Installation Success

Preparing for a trade show project requires a lot of planning, from site inspections and product choices to printer setup and installation. In the video above, trade show printing and installation pro Keith Bernard of Now That’s a Wrap, shares his advice, stemming from years of experience, including:

  • Booth sizing
  • Site inspections
  • Product choices
  • Printer and media settings
  • Installation success

He highlights the key steps you should take when planning, creating and setting up the display so everything goes smoothly from start to finish. For example: “You’ve got to talk about whether the graphics will be used inside or out,” he says, “and what could potentially damage the display, fade the ink or could have issues with glare.”

Asking your customer the correct questions will ensure their graphics stand out above all the competition. Taking the time to get the right team members in place and planning ahead will allow your customer to focus on their business at the show, while their graphics are performing seamlessly in the background.

How the Pros Prep for Trade Shows

Chances are, you’ve been to many trade shows. As a printer, installer or spectator, you know that trade show displays can range from the very simple to the extremely elaborate. The key to pulling off a trade show display without a hitch is good communication with customers upfront.

For help, we turned to two industry pros, Kaine Guidry, a former OEI employee and current print technician in LexJet’s Experience Center, and Bernie Raymond, production manager at Morley, which designs, engineers, fabricates and installs trade show exhibits.